With the increasingly fierce market competition in the electronic industry, the  printer die cutter slotter machine manufacturers are moving towards a large-format development trend. The printing press manufacturers also stipulate that the diameter of the printing press manufacturers’ roll is becoming larger and larger, and the quality of the roll printing press manufacturers becomes higher and higher. With the technical development trend of standard air pressure, the full-automatic printing machine manufacturers can fold up the large format of 2.1m, the speed can reach above 80m/min, the film diameter can reach 1m, and the production capacity can reach 400kg/h. The traditional printing machine manufacturers are not only inconvenient in actual operation, but also have high energy and labor efficiency in the whole process of organizing printing machine manufacturers, and it is very easy to cause waste when dividing into several films (three on one side) or making small films. In order to deal with the above problems, this paper introduces in detail how to select the printing machine manufacturer organization of PLC control printing machine manufacturer to complete the automatic printing machine manufacturer.

The printer slotter die cutter machine manufacturer traditional printing machine manufacturer organizes the following components: the lower wheel equipment, the length counting equipment, and the dual-station winder. The wheel plate equipment is located on the printing machine manufacturer. The handle of the printing machine manufacturer shakes, and the drive chain pushes the wheel plate support frame and the mechanical arm to turn over. The length counter receives the data signal from the limit switch and sends it to the electronic counter for counting once per meter. The parents of the printing press factory set the length independently in advance. When the winding length reaches the set length, the alarm warning light will alarm. The dual-station winding machine is composed of A winding and B winding. It is selected to be in the passive winding mode, and uses the speed in the extrusion tap big rubber stick and the winding roller to roll up the printing machine manufacturer with stable support.

The press manufacturer’s drive is driven by two vector material frequency conversion governors independently operating the reducer. A. B. The rotation speed ratio of the printing machine manufacturer is the same, which is reversed, so as to achieve the goal of simultaneous winding on both sides. A. B. The winding speed and winding support force of the printing machine manufacturer can be adjusted separately, and there is no harm to each other, so as to obtain good actual winding effect of the printing machine manufacturer. The system software of this printer manufacturer is in passive winding, and its winding quality is inferior to that of the printer manufacturer. To a large extent, it lies in the inclined motion track of the slide rail curve of the winding inflatable shaft. In the whole process of the traditional printing machine manufacturer, when the unwinding diameter meets the requirements, the printing machine manufacturer will be launched. Move the prepared inflatable roll to the upper side of the rubber stick (the preparation station), manually decorate and partition the printing machine manufacturer, move the membrane roll to the bow end of the fishbeam end, and shake the handle of the printing machine manufacturer. The newly replaced wind-up inflatable shaft will gradually move to the wind-up station, and the printing machine manufacturer will proceed.

The disadvantage of the traditional printing machine manufacturer organization is that the printing machine manufacturer has high energy and labor efficiency in the actual operation during the whole process. When the winding is full, the alarm is given. One person shakes the handle of the printing machine manufacturer to shake the inflatable shaft on the wheel plate into the waiting area. Two people move the full roll to the imperial roll area at the same time, and then the manual laser cuts off the printing machine manufacturer. The whole process needs the cooperation of three people. When the paper box printing and slotting die-cutting machine manufacturer is divided into several films (above three films on one side) or is a small film printing machine manufacturer, the printing machine manufacturer needs a large number of people to cooperate with each other. The printing machine manufacturer is not proficient in cooperation with each other or the use is unreasonable, which is very easy to cause waste.

The manual printer manufacturer changed to the full-automatic printer manufacturer. On the basis of the traditional printer manufacturer’s organization, the full-automatic printer manufacturer has improved the full-automatic roll up, full-automatic disconnect, full-automatic roll delivery and other functions. The update and transformation of the system software of the full-automatic printing machine manufacturer removed the handle of the printing machine manufacturer on the basis of the manual printing machine manufacturer, and a reducer was refitted on it, which was controlled by PLC as a rotating power device. The printing machine manufacturer lifts a laser cutting cylinder (rodless cylinder) on the rotary shelf. The cylinder shaft of the printing machine manufacturer is composed of a high pressure regulating valve, a shuttle valve, an airlock valve, a leading type of this product, a flow valve and other control components. The darts on the rodless cylinder shaft are used for back and forth laser cutting fitness exercise; At the same time, a magnetic cylinder is lifted on both sides to supply air to the rodless cylinder.

Full-automatic coil feeding is carried out by lifting a magnetic cylinder and a mechanical arm on both sides of the printing machine manufacturer. The shaft is connected to each other to form a symmetrical character. In the air supply, a high pressure regulating valve, a shuttle valve, an airlock valve, a leading type of this product, a flow valve and other control components are lifted. The printing machine manufacturer moves the cylinder pressure when the roll is full. The printing machine manufacturer makes the moving cylinder extend forward to release the full roll to the imperial roll area and is locked by the mechanical code lock, The rear moving cylinder is connected in place, and the moving cylinder maintains the working pressure.

If you are also interested in this machine,please don’t hesitate to contact us:

Overseas manager: Tom Wang

Email:cartonmachine.tomwang@aliyun.com

Phone/Wechat/Whatsapp:+86 13303078975