The standardized operation process of the water ink printing slotting machine .At present, most of the printing machinery and equipment use the water tank immediate power supply system. The water circulation depends on the pressure difference. The proper pressure difference can keep the power supply system uniform, so the occurrence of the pressure difference should be standardized as much as possible. Do not fill the water tank when filling water to prevent negative working pressure and dirty water. In addition, pay attention to the good airtightness of the drain hole on the water tank. If the airtightness is not suitable, the water flow will be unstable. After the water in the water tank of the ink printing slotting machine is used up, the residual liquid in it should be cleaned and clean, and the ink printing slotting machine should be filled with new fountain solution.

In addition to the immediate power supply system for the water tank of the ink printing slotting machine, there are also some machines and equipment that use electric water, that is, according to the water pump of the ink printing slotting machine, the water in the water tank is sent to the ink printing slotting machine. This method can cycle the power supply system, but it is convenient to prevent the dirt from entering the ink printing slotting machine again. Therefore, the ink printing slotting machine is equipped with a filter system at the total population of the centrifugal pump, The system should be filtered on time. There is also a way of power supply system that alcohol is wet. According to a water tank, the fountain solution is sent to each color deck. The ink printing slotting machine should pay attention to the mixed occupancy rate of alcohol and water, which is generally 25%. In addition, the indoor temperature should not be too high, otherwise the alcohol volatilization is more serious.

The standardized operation process of the water ink printing slotting machine and the water ink printing slotting machine roll can be added by the water tank or manually made immediately, but the workload at the back is larger. The water in the water ink printing slotting machine cannot be too much, otherwise it may flow out, and the water in the water ink printing slotting machine cannot be too little, otherwise the capacity of the water ink printing slotting machine is poor. The pH value of the fountain solution is generally adjusted to about 4-6. The residual solution in the ink printing slotting machine should be removed every day after work to prevent the corrosion of the ink printing slotting machine.

Pay attention to the assembly position of the ink printing slotting machine and the reasonable layout of the upper sewage pipe. If the ink flexo printing die cutting slotting machine is not installed properly or the water pipe is not smooth, it should be adjusted immediately. The height of water feeding is determined by changing the transmission ratio of the roller of the ink printing slotting machine. The rotation of the roller of the ink printing slotting machine is driven by the water roller motor. The position of the water roller motor of some machines and equipment is inappropriate or other reasons often cause the roller of the ink printing slotting machine to not rotate or the transmission ratio is uneven. At this time, the reasons should be found out in detail.

Some machines and equipment in the monochrome and dichromatic machines cannot be locked at work. If you see this situation, you should immediately adjust it. In addition to the automatic water inlet of the ink printing slotting machine, there are also some machines and equipment that use the manual water inlet to immediately pour the water into the ink printing slotting machine. However, the water volume in the ink printing slotting machine should always be observed during printing. When the printing plate is dirty, it is necessary to use the emergency water inlet method. Generally, the plastic bottle with nozzle of the ink printing slotting machine is used to add water to the water transfer roller or the water outer roller. Pay attention not to immediately add water to the water roller. You can also choose the way of overall water inflow of the ink printing slotting machine (that is, expand the angle or transmission ratio of the ink printing slotting machine roll, and then repair to the previous condition after removal).

Some ink printing slotting machines are equipped with emergency water feeding equipment. Sponge can also be used to control the specification of water quantity for some water inflow (wet the sponge and squeeze it by hand). When the water volume exceeds the normal specification, the water volume can be reduced by reducing the transmission ratio or rotation angle of the roller of the ink printing slotting machine. If a part of the water in the ink printing slotting machine can be installed with a scraper or nozzle to reduce the water volume, a small paper strip can also be pasted on the roll of the ink printing slotting machine, and the other end can be pasted on the ink printing slotting machine, and the excess water volume on the roll of the ink printing slotting machine can be absorbed according to the small paper strip. This kind of method can reduce the number of prints. When the number of prints is large, it is easy to enter the water path along with the roller of the ink printing slotting machine because the stress of the printing paper is reduced due to moisture and heat.

If you are also interested in this machine,please don’t hesitate to contact us:

Overseas manager: Tom Wang

Email:cartonmachine.tomwang@aliyun.com

Phone/Wechat/Whatsapp:+86 13303078975